problems faced with Qt everywhere for Mini 2440

Tweet

After applying what i said in this post , some problems occurred
1.arm-none-linux-gnueabi: command not found
solution:
 -in terminal:

gedit .bashrc

 -in  .bashrc make sure that those line are there , if not there add them:

export PATH=/usr/local/arm/4.3.2/bin:$PATH

export PATH=/usr/local/arm/4.3.2/arm-none-linux-gnueabi/bin:$PATH 

save .bashrc and exit all the open linux terminals.

then in qt-everywhere directoy browse to the mkspecs/qws/linux-arm-g++/ then edit the qmake.conf
replace all the contents of this file with the following:

1. #  
2. # qmake configuration for building with arm-linux-g++  
3. #  
4.   
5. include(../../common/g++.conf)  
6. include(../../common/linux.conf)  
7. include(../../common/qws.conf)  
8.   
9.   
10.   
11. # modifications to g++.conf  
12. QMAKE_CC                = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-gcc  
13. -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t -mtune=arm920t -O0   
14.   
15. QMAKE_CXX               = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-g++  
16. -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t -mtune=arm920t -O0   
17.   
18. QMAKE_LINK              = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-g++  
19. -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t -mtune=arm920t -O0   
20.   
21. QMAKE_LINK_SHLIB        = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-g++  
22. -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t -mtune=arm920t -O0   
23.   
24.   
25.   
26. # modifications to linux.conf  
27. QMAKE_AR                = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-ar cqs  
28. QMAKE_OBJCOPY           = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-objcopy  
29. QMAKE_STRIP             = /usr/local/arm/4.3.2/bin/arm-none-linux-gnueabi-strip  
30.   
31.   
32.   
33. QMAKE_CFLAGS    += -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t  
34. -mtune=arm920t  
35. QMAKE_CXXFLAGS    += -msoft-float -D__GCC_FLOAT_NOT_NEEDED -march=armv4t  
36. -mtune=arm920t  
37.   
38.   
39. load(qt_config)  

then save the file and close it.
finally browse to the Qt-everywhere directory in the terminal and  configure with these options

./configure -release -embedded arm -xplatform qws/linux-arm-g++ -prefix /usr/local/Qt-4.6.2_arm -little-endian -no-webkit -no-qt3support -no-cups -no-largefile -nomake examples -optimized-qmake -no-openssl -nomake tools

then make .. then make install .. tada .. you'll find Qt-everywhere's output folder in /usr/local/ under the name

Qt-4.6.2_arm

good luck with your steps
--------------------------------------------------------------------------------------------
the code above was formatted using this tool
it seems to be great online tool

Tweet